Dry Ice Cleaning With Inlet and Outlet Pressure in View
The HTS828 blasts 3 mm dry ice pellets from a 7.5 kg hopper and shows inlet supply and outlet working pressure on two separate gauges, so you can adjust ice delivery from 0 to 3.2 kg/min against a stable reading. It runs on an external dry-air compressor, which is not included.
- Dual Pressure Gauges
- 0โ3.2 kg/min Ice Feed
- 7.5 kg Hopper
- Oil-Water Separator
Key Features
-
Dual Pressure Monitoring
Inlet supply and outlet working pressure are shown separately while you check blasting stability.
-
Adjustable Dry Ice Feed
Delivery adjusts from 0 to 3.2 kg/min; increase gradually to find a tested setting for each surface and task.
-
Moisture and Clumping Control
A large oil-water separator and spiral feed help reduce wet-air clumping and line blockage.
-
Mobile Workshop Layout
Metal housing, emergency stop, gun holder, handle and casters for moving between bays.
-
No Blasting Media Left Behind
Pellets sublimate, so there is no solid media to clean up โ only the carbon, oil and debris removed from the part.
HTS828 vs HTS818
| HTS828 | HTS818 | |
|---|---|---|
| Pressure gauge | Dual (inlet / outlet) | Single |
| Compressed-air flow | >1โ2 mยณ/min | >1โ3 mยณ/min |
| Hopper / ice feed | 7.5 kg / 0โ3.2 kg/min | 7.5 kg / 0โ3.2 kg/min |
What’s in the Box
- HTS828 dry ice blasting machine
- Blasting gun with hose
- Spray nozzle and scraper set
- Air inlet hose with valve, ground cable and clamp cables
- Ice scoop, spare fuses, gloves, safety goggles and earplugs
- User manual
How to Use
- Verify the setupConfirm external air above 1โ2 mยณ/min within 0.3โ1.0 MPa, correct power, 3 mm pellets and ventilation.
- Inspect air treatment and connectionsCheck the separator, hoses, gun, ground and emergency stop; purge moisture.
- Load fresh dry iceAdd 3 mm pellets and keep foreign material out of the hopper.
- Test with low settingsWatch both gauges on a suitable test area before increasing pressure or feed.
- Clean and collect debrisKeep output stable and contain the loosened contamination.
- Clear, isolate and inspectSet feed to zero, clear the path as the manual describes, disconnect air and power, then inspect hoses and nozzles.
Full operating and troubleshooting steps: HTS828 user manual (PDF).
Good to Know
Caution
- Air compressor and dry ice are not included. Verify more than 1โ2 mยณ/min at working pressure, dry air, and hose and fitting capacity.
- COโ, cold and noise: ventilate the area and wear gloves, goggles, hearing protection, protective clothing and closed-toe shoes.
- Test a small area first around sensors, coatings, plastics, rubber and aged surfaces.
- Connect only to a grounded supply of the correct regional voltage.
Care
- The gauges are monitoring tools; they do not replace surface tests, the vehicle procedure or operator control.
- Plan how removed carbon, oil and debris will be collected.
FAQ
What air supply does the HTS828 require?
0.3โ1.0 MPa and more than 1โ2 mยณ/min; normal operation begins from 4 bar. Confirm the actual dynamic output of your compressor.
What do the two gauges show?
Inlet air pressure and outlet working pressure, displayed separately.
What dry ice does it use?
3 mm pellets, loaded into the 7.5 kg hopper.
Does dry ice cleaning remove all cleanup?
No. No solid media remains, but the removed contamination still needs collecting and the COโ requires ventilation.
Is it safe for every sensor or coating?
No. Use conservative, tested settings and confirm the material or coating is suitable first.
English 
German 
Spanish 