Stable Battery Support for ECU Programming, Plus Charging and Start Assist
The EM365 provides a stable power supply during vehicle ECU programming, helping maintain consistent voltage throughout the process. It also features battery recovery and fast charging functions. By switching between different operating modes, the EM365 can be used as a 12V automotive battery charger, an emergency jump starter, or a reliable power supply for vehicle maintenance and diagnostic tasks in automotive repair workshops.
- Up to 150 A Programming
- Voltage range 50Hz–60Hz
- 20 A Charging
- 400 A Start Assist
- 5 Work Modes
Key Features
-
Programming Power Supply
Set the voltage the vehicle procedure calls for, or choose fixed 14 V, and watch output voltage and current on the color screen.
-
Intelligent Charging
Adjusts voltage and current as charging progresses, with progress and completion shown on screen.
-
Battery-Type Settings
Standard lead-acid, AGM flat plate, AGM spiral and GEL; EFB through External Charging with the battery removed.
-
Vehicle Display Mode
Holds a float charge and raises output when loads discharge the battery, for showroom and display work.
-
Battery Restoration
A treatment mode for discharged or long-idle lead-acid batteries; results depend on condition and sulfation.
-
Forced Start
400 A / 12 V momentary starting support, guided by an on-screen prompt.
More Specifications
| Thermal recovery | Full current returns when the unit cools to 50 °C |
|---|---|
| Controls | Physical buttons, adjustable screen brightness, selectable interface languages |
| Cooling | High-speed cooling fan |
Model Comparison
| EM355 | EM365 | EM385 | |
|---|---|---|---|
| Maximum programming current | 120 A / approx. 3 min | 150 A / approx. 3 min | 150 A / approx. 3 min |
| Work modes | Programming, charging, restoration | Programming, charging, restoration, vehicle display, forced start | Programming, fast charging, restoration, vehicle display, forced start |
| Lithium (LFP/NCM) charging | No | No | Yes, battery removed |
| Separate adjustable supply | No | No | Yes |
| Forced start | No | 400 A / 12 V | 400 A / 12 V |
What’s in the Box
- 1×EM365 inverter programming power supply
- 1×Battery clamp output cable
- 1×AC power cable (plug type depends on version)
- 1×User manual

How to Use
- Prepare the vehicleCheck the support voltage the procedure requires and make sure the 12 V battery is fully charged.
- ConnectUse a correct, grounded AC supply, keep vents clear, and clamp red to positive and black to negative.
- Select programming powerChoose Programmable Power Supply with the arrow keys, press OK and follow the prompts.
- Set the voltagePick Adjustable Mode and enter the required voltage, or Fixed Mode for 14 V.
- Run and monitorConfirm the displayed voltage and current, then run the procedure with your programming tool until it completes.
- Stop outputStop output before changing settings, switching tasks or disconnecting.
Menus, connections and safety: EM365 user manual (PDF).
Good to Know
Caution
- Lithium batteries are not supported. EFB charging and Battery Restoration require the battery to be removed from the vehicle.
- Peak output lasts about 3 minutes before thermal limiting; confirm the mode, voltage and available current cover the full programming event.
- Connect clamps with correct polarity on clean, secure terminals before enabling output.
Care
- Use in a dry, ventilated location with the vents clear.
- When charging ends, stop charging before removing the clamps.
FAQ
Does the EM365 program the ECU itself?
No. It supplies power during programming; use separate programming or diagnostic equipment for the ECU work.
Why use programming mode instead of charging?
Programming mode holds the support voltage you choose; charging mode changes output as the battery charges.
Which programming voltage should I select?
The voltage given in the vehicle procedure. Fixed Mode suits jobs that call for 14 V.






































