Dry Ice Carbon Cleaning With Supply and Working Pressure in View
The HTS709 removes carbon, oil and other suitable contaminants with dry ice instead of water or chemical solvents, showing inlet air and outlet working pressure on separate gauges while you set ice delivery. It needs an external dry compressed-air supply and dry ice, neither of which is included.
- Twee manometers
- 7.5 kg Hopper
- Ijstoevoer van 0–3.2 kg/min
- Olie-waterafscheider
- 4 Nozzle Types
Key Features
-
Bewaking van inlaat- en uitlaatdruk
Separate gauges show incoming air pressure and outlet working pressure, so supply and blasting conditions can be checked during cleaning.
-
Instelbare ijstoevoer
Raise output gradually while watching both gauges, then keep the setting tested on a small area for the surface and task.
-
Vocht- en klonterbeheersing
A large oil-water separator and spiral feed reduce moisture-related clumping, line blockage and interrupted delivery.
-
Fewer Refills
The 7.5 kg internal hopper extends continuous operation during repeated workshop cleaning.
-
Overzichtelijke mobiele bediening
Push handle, control panel, emergency stop, gun holder, air and gun interfaces, and four 360° wheels keep operating points within reach.
-
Geen vast straalmiddel achtergebleven
Pellets at about -78.5°C make deposits brittle, then sublimate on impact and expand nearly 800 times to lift them; only the removed carbon and oil remain to collect.
Meer specificaties
| Luchtdruk bij opstarten | Werkt zodra de toevoer hoger is dan 4 kgf/cm² |
|---|---|
| Werkreferentie | About 4–6 min and 3–5 kg of dry ice per four-cylinder or intake-port clean; varies with deposits, conditions and settings |
| Geschikte voertuigen | Brandstof-, hybride en elektrische voertuigen |
HTS709 vs HTS708
| HTS709 | HTS708 | |
|---|---|---|
| manometer | Dubbel (inlaat / uitlaat) | Single |
| Luchtstroom | >1–2.0 m³/min | >1–3.0 m³/min |
| Rated power | 1100 W | 550 W |
| Netto- / brutogewicht | 63 kg / 90 kg | 60 kg / 88 kg |
| Trechter / ijstoevoer | 7.5 kg / 0–3.2 kg/min | 7.5 kg / 0–3.2 kg/min |
Inhoud van de doos
- HTS709-droogijsreinigingsmachine
- 3 m straalslang
- Spuitpistool en verlengbuizen
- Luchtinlaatslang met ventiel
- Klemkabels en aardingskabel
- IJsschep, reservezekeringen en koppelingen
- Handschoenen, veiligheidsbril en oordoppen
- User manual
How to Use
- Controleer de opstellingCheck voltage against the nameplate, and prepare dry compressed air, fresh pellets, grounding and ventilation.
- Inspecteer de aansluitingenCheck hoses, nozzle, grounding, separator and control state before loading.
- Purge moistureRun air with the feed at zero until condensate is cleared.
- Load and testLoad 3 mm pellets and start with a conservative setting on a suitable test area.
- Bewaak beide drukkenWatch the inlet and outlet gauges and adjust output gradually for the task.
- Collect debrisThe dry ice turns to gas, but loosened carbon and oil still need collecting.
- Wis en schakel uitSet feed to zero, clear the line as directed, isolate air and power, and inspect wear parts.
Full loading, operating and troubleshooting steps: HTS709-gebruikershandleiding (PDF).
Good to Know
Let op
- Compressor and dry ice are not included. A dehumidifying compressor is recommended to prevent clumping and moisture problems in the lines.
- Connect only to a grounded (earthed) socket that matches the machine’s voltage.
- CO₂, cold and noise: ventilate the area and wear cold-resistant gloves, goggles, hearing protection, protective clothing and closed-toe shoes. Avoid skin contact with dry ice.
- Never aim the nozzle at people, and clear residual pellets before shutdown.
- Test coatings and materials on a small area first, and use lower settings around sensitive surfaces. Use on intake valves or combustion chambers only where the vehicle procedure permits.
Onderhoud
- The gauges aid monitoring; material, coating, nozzle, distance, pressure, airflow and operator procedure still decide whether cleaning is suitable.
FAQ
Kan droogijsstralen lak verwijderen?
It can remove failing or weakly bonded paint, but its mild-to-medium strength may not be enough for well-bonded coatings; paint type and primer affect the result.
Verwijdert het roest?
It removes loose surface rust, oxidation and salt, but not deeply adhered rust or pitting. Because it is non-abrasive, it cannot produce a white-metal finish.
Wat heb ik nog nodig om te beginnen?
A compressed-air source, power supply and dry ice supply. With a portable diesel compressor, an aftercooler helps remove moisture and cool the air.
Waar kan ik droogijs krijgen?
Pellets or blocks are usually available from industrial gas suppliers, welding supply companies and local suppliers, either as needed or on regular delivery.
English 
Deutsch 
Español 
Nederlands 
Français 