Key Programming, ECU Cloning and OE-Level Diagnostics in One Full Kit
The MaxiIM IM608S II / IM608 Pro II tablet works with the included XP400 Pro key programmer and MaxiFlash JVCI+ for immobilizer and key work, including all keys lost, and adds full-system diagnostics, ECU coding and bi-directional control. G-BOX3, APB112 and IMKPA are part of this kit.
- XP400 Pro + JVCI+
- G-BOX3 + APB112 + IMKPA
- All Keys Lost / Read PIN
- BBA ECU & TCU Cloning
- 40+ Services
Hauptmerkmale
-
IMMO and Key Programming
Read PIN/CS with all keys lost, key generation, key learning and remote learning; IMMO data backup and restore, IMMO ECU reset, adaptation, refresh and coding.
-
Smart and Expert Modes
Smart Mode guides and automates key learning; Expert Mode gives access to advanced key learning.
-
Chip-Level Read/Write
Transponder read/write and EEPROM/MCU read/write through the XP400 Pro.
-
Mercedes-Benz ECU and TCU Cloning
Adds Mercedes-Benz ECU and TCU cloning, completing ECU cloning coverage for Mercedes, BMW and Volkswagen.
-
OE-Level Diagnostics
The same diagnostic capability as the Elite II: read and erase DTCs and view live data on all modules, with direct access to EPB, DPF, SAS, SRS, oil reset, ABS bleeding and BMS.
-
ECU Coding and Bi-Directional Control
Change pre-programmed ECU options, activate, match, code and relearn replaced modules, and test subsystems or components to check system integrity.
-
Cloud Reports
Maintenance reports are stored in the cloud so device and test records can be viewed anytime.
More Specifications
| Connectivity | Wi-Fi (802.11 a/b/g/n/ac), USB 2.0, BT v.2.1 + EDR, SD card (up to 64GB), HDMI |
|---|---|
| Sensors | Light sensor for automatic brightness |
| Charging | 12 V AC/DC power supply |
| Power consumption | 6.5 W |
| Operating temperature | 0 to 50°C (32 to 122°F) |
| Storage temperature | -20 to 60°C (-4 to 140°F) |
| Protocols | ISO 9142-2, ISO 14230-2, ISO 15765-4, K/L-Line, Flashing Code, SAE-J1850 VPW, SAE-J1850 PWM, CAN ISO 11898 (high-, middle-, low-speed and single-wire CAN), GM UART, UART Echo Byte, Honda Diag-H, TP 2.0, TP 1.6, SAE J1939, SAE J1708, Fault-Tolerant CAN |
What’s in the Box
- MaxiIM IM608 Pro II / IM608S II tablet
- MaxiFlash JVCI+
- XP400 Pro key programmer
- G-BOX3
- APB112
- IMKPA key programming adapter set
- Main cable, USB cable, mini USB cable and APC101 USB cable
- AC/DC adapter and auxiliary power outlet adapter
- Spare fuses 6 × 30 mm (2 pcs)
- AAC001
- USB to Ethernet adapter
- MCU adapters APB104 (FQFP64), APB105 (FQFP80), APB106 (FQFP112), APB107 (FQFP144) and APB108 (FQFP176)
- APB129 EEPROM adapter
- APB125 Mercedes infrared collector
- APA002 EEPROM socket, APA103 EEPROM clamp and APA101 signal cable
- APA107 ECU cable, APA108 MCU cable and APA109 MC9S12 cable
- Connect cable
- Quick reference guide and packing list
- Carrying case (634 × 170 × 404 mm)
Good to Know
Caution
- Under a North American IP address, the MaxiIM IM608 series requires an active NASTF SDRM subscription, which is not included and must be purchased separately.
English 
German 
Spanish 