Full-Kit Key Programming, IMMO and OE-Level Diagnostics on a 10.1-Inch Tablet
This full kit pairs the IM608S II / IM608 Pro II tablet with the XP400 Pro key programmer and MaxiFlash JVCI+, and adds the G-BOX3, APB112 and IMKPA adapters. It handles immobilizer and key work, including read PIN/CS with all keys lost, alongside full-system diagnostics, ECU coding and bi-directional control. In North America an NASTF SDRM subscription is required and sold separately.
- XP400 Pro + JVCI+
- G-BOX3, APB112 & IMKPA
- All Keys Lost / Read PIN
- Smart & Expert Modes
- ECU Coding
Key Features
-
Complete Key and IMMO Functions
Read PIN/CS with all keys lost, key generation, key learning and remote learning, IMMO data backup and restore, IMMO ECU reset, adaptation, refresh and coding.
-
Transponder, EEPROM and MCU Read/Write
Read and write transponders, EEPROMs and MCUs through the XP400 Pro and the included adapters.
-
Smart and Expert Modes
Smart Mode guides and automates key learning; Expert Mode is for advanced key learning.
-
OE-Level Diagnostics
The same diagnostic capability as the Elite II: diagnose all modules, read and erase DTCs and view live data on more than 80 U.S., Asian and European makes.
-
Maintenance Services
Direct access to EPB, DPF, SAS, SRS, oil reset, ABS bleeding and BMS functions.
-
ECU Coding and Bi-Directional Control
Change pre-programmed options, activate, match, code and relearn replaced modules, and test subsystems and components to check system integrity.
-
Cloud Reports
Maintenance reports are stored in the cloud, so device and test records can be viewed anytime.
More Specifications
| Connectivity | Wi-Fi (802.11 a/b/g/n/ac), USB 2.0, BT v2.1 + EDR, SD card (up to 64GB), HDMI |
|---|---|
| Charging | 12 V AC/DC power supply |
| Power consumption | 6.5 W |
| Sensors | Light sensor for automatic brightness |
| Operating temperature | 0 to 50°C (32 to 122°F) |
| Storage temperature | -20 to 60°C (-4 to 140°F) |
| Protocols | ISO 9142-2, ISO 14230-2, ISO 15765-4, K/L-Line, Flashing Code, SAE J1850 VPW and PWM, CAN ISO 11898 (high, middle, low speed and single-wire), GM UART, UART Echo Byte, Honda Diag-H, TP 2.0, TP 1.6, SAE J1939, SAE J1708, Fault-Tolerant CAN |
What’s in the Box
- 1×MaxiIM IM608S II main unit
- 1×MaxiFlash JVCI+
- 1×XP400 Pro key programmer
- 1×G-BOX3
- 1×APB112
- 1×IMKPA
- 1×Main cable
- 1×USB cable
- 1×Mini USB cable
- 1×AC/DC adapter
- 2×Spare fuses (6 × 30 mm)
- 1×Auxiliary power outlet adapter
- 1×AAC001
- 1×USB to Ethernet adapter
- 1×APC101 USB cable
- 1×APB104 MCU_FQFP64
- 1×APB105 MCU_FQFP80
- 1×APB106 MCU_FQFP112
- 1×APB107 MCU_FQFP144
- 1×APB108 MCU_FQFP176
- 1×APB129 EEPROM adapter
- 1×APB125 Mercedes infrared collector
- 1×APA002 EEPROM socket
- 1×APA101 signal cable
- 1×APA103 EEPROM clamp
- 1×APA107 ECU cable
- 1×APA108 MCU cable
- 1×APA109 MC9S12 cable
- 1×Connect cable
- 1×Quick reference guide
- 1×Packing list
- 1×Carrying case (634 × 170 × 404 mm)
Good to Know
Caution
- Under a North American IP address, the MaxiIM IM608 series requires an active NASTF SDRM subscription, which is not included and must be purchased separately.
English 
German 
Spanish 