Longer Dry Ice Cleaning Runs Between Refills
The HTS708 cleans suitable automotive and industrial surfaces without water or chemical solvent, using a 7.5 kg hopper, adjustable ice delivery and a 3 m hose. It needs an external compressed-air supply and locally sourced dry ice, neither of which is included.
- 7.5 kg Hopper
- Alimentation en glace de 0–3.2 kg/min
- 3 m Blast Hose
- Manomètre unique
Key Features
-
Fewer Refills
The 7.5 kg tank extends cleaning time between refills during repeated workshop use.
-
Débit de glace réglable
Set the ice amount on the control panel to match a tested setting for each task rather than one intensity for every surface.
-
Traitement de l’air pour une alimentation stable
A built-in filter helps reduce moisture-related clumping and feed interruption.
-
Nettoyage physique à sec
Pellets at about -78.5 °C embrittle deposits, then sublimate and expand on impact to lift them; no blast media or chemical residue remains.
-
Corps d’atelier mobile
Pull handle, 360° casters, ice output knob and dedicated air-source and gun connections for setup and movement around the bay.
Autres caractéristiques
| Principe de fonctionnement | Projection de glace carbonique |
|---|---|
| Consommation de rinçage | 3–5 kg |
| Compresseur recommandé | 1.5 m³/min avec un réservoir d’air de 300 L |
HTS708 vs HTS709
| HTS708 | HTS709 | |
|---|---|---|
| manomètre | Single | Dual |
| Débit d’air | >1–3.0 m³/min | >1–2.0 m³/min |
| Rated power | 550 W | 1100 W |
| Poids net / brut | 60 kg / 88 kg | 63 kg / 90 kg |
| Trémie / alimentation en glace | 7.5 kg / 0–3.2 kg/min | 7.5 kg / 0–3.2 kg/min |
Contenu du coffret
- Machine de nettoyage par projection de glace carbonique HTS708
- Tuyau et pistolet de projection
- Tubes de buse et pelle à glace métallique
- Flexible d’entrée d’air avec vanne
- Câbles d’alimentation et de masse, fusibles de rechange
- Gants, lunettes de protection et bouchons d’oreilles
- User manual
How to Use
- Préparez le systèmeConfirm compressor, dry air, grounded power, fresh pellets, ventilation, nozzle and PPE.
- Inspectez les raccordementsCheck hoses, gun, ground and machine before loading dry ice.
- Purgez les condensatsSet ice feed to zero and check whether moisture exits the nozzle.
- Chargez et réglez la sortieUse 3 mm pellets, start conservatively and test a small approved area.
- Nettoyez et surveillezWatch delivery and pressure, adjust gradually and collect removed contamination.
- Retirez la glace restanteSet output to zero and run the gun for about 30 seconds to clear the tray and tube.
- Arrêter et inspecterDisconnect air and power, then inspect the hose, nozzle and separator.
Loading, adjustment, maintenance and troubleshooting: Manuel d’utilisation HTS708 (PDF).
Good to Know
Attention
- Compressor and dry ice are not included. Confirm at least 90 psi with adequate dynamic flow and dry air, and confirm a local dry ice supply before ordering.
- Dry ice is solid CO₂: ventilate the area, avoid skin contact and wear goggles, hearing protection, gloves, work clothes and closed-toe shoes.
- Test a small area first on paint, rubber, plastics, labels and aged coatings.
- Confirm voltage, plug and protective earth match your supply before use.
Entretien
- Keep the hopper clean and free of foreign objects when adding ice.
- Loosened dirt and carbon still need to be collected after cleaning.
FAQ
Quelle taille de pellets dois-je utiliser ?
3 mm pellets are preferred. Pellets up to 8 mm may be used when suitable for the nozzle, air supply and setup.
Peut-il retirer la peinture ou la rouille ?
It can remove loose or weakly bonded paint, surface rust, oxidation and salt. It will not remove well-adhered paint, deep rust or pitting, and it does not produce a white-metal finish.
Comment se compare-t-il au HTS705 ?
The HTS705 has a 5 kg tank; the HTS708’s 7.5 kg tank means fewer refills.
Un flexible plus long est-il disponible ?
The standard hose is 3 m; a hose up to 5 m can be made to order at extra cost.
English 
Deutsch 
Español 
Nederlands 
Français 